JL Audio XD400/4: 4 Channel Class D Full-Range Amplifier 400 Watts

217 mm x 180 mm x 52 mm. X 2. 05 in. 50 hz | input range: 100mv - 4v rms | Dimensions L x W x H: 8. 52 in. X 7. 09 in. Thd at rated power: 104 db referred to rated power a-weighted, 20 Hz-20 kHz noise bandwidth | >84 dB referred to 1W A-weighted, 20 Hz-20 kHz noise bandwidth. Rated power 14. 4 v stereo: 75w rms x 4 @ 4 ohms 100w rms x 4 @ 2 ohms | rated power 14.

4 v bridged: 150w rms x 2 @ 8 ohms 200w rms x 2 @ 4 ohms | rated power 12. 5 v stereo: 60w rms x 4 @ 4 ohms 90w rms x 4 @ 2 ohms | Rated Power 12. 5 v bridged: 120w rms x 2 @ 8 ohms 180w RMS x 2 @ 4 ohms. Frequency response: 12 hz - 22 khz +0, -1db | damping factor: >150 @ 4 ohms per ch. 50 hz | >75 @ 2 ohms per ch.

Xd400/4 jl audio 4 channel amp 400 w component speakers tweeters amplifier new description: 400w 2/3/4 channel amplifier | inputs: two stereo pairs | Speaker output connections: Accept up to 12 AWG wire | +12V and Ground connections: Accept up to 4 AWG wire.

JL Audio HD-RLC Amplifier Remote Level Control and Cable

The hd-rlc remote level controller works with jl audio's HD Series and XD Series amplifiers and many marine amps, allowing you to manage your level settings from the front of your vehicle. The hd-rlc remotely controls the bass level of the following jl audio amplifiers:hd-series: all modelsXD-Series: All modelsMHD-Series: All modelsM-Series: M600/1, M500/3, M200/2, M700/5, M400/4, M600/6.

When the hd-rlc is connected to the above amplifiers, it acts as an attenuator on the input gain of the amplifier and is used to adjust the overall level of the amplifier from the front of the vehicle. The hd-rlc kit includes the rotary control with a black ABS knob, mounting hardware and one 18 ft. The hd-rlc adjusts your amplifier's level, not its "bass boost, " so you maintain the same bass quality as you turn the volume up and down.

. 5. 5 m cable.


Similar products

JL Audio XD600/1v2 Mono subwoofer amplifier - 600 watts RMS x 1 at 2 ohms
JL Audio XD700/5v2 5-channel car amplifier - 75 watts RMS x 4 at 4 ohms + 300 watts RMS x 1 at 2 ohms
JL Audio XD-PCS4-1B 4-AWG 12-Volt Power Connection for Single Amplifier 100-AMP Capacity
JL Audio RBC1 Remote Bass Control
HD1200/1 - JL Audio Monoblock 1200W Subwoofer Speaker Amplifier
HD750/1 - JL Audio Monoblock 750 Watt HD Amplifier
JL Audio XD-CLRAIC2-18 2-Channel Twisted-Pair Audio Interconnect Cable with Molded Connectors, 18-Feet
JL Audio XD-CLRAIC4-18 4-Channel Twisted-Pair Audio Interconnect Cable with Molded Connectors, 18-Feet


JL Audio XD1000/1v2 Monoblock Class D 1000W Subwoofer Amplifier

Monoblock class d subwoofer amplifier RMS Power Rating: 2 ohms: 1000 watts x 1 chan. Mono channel operation One pair of pre-amp outputs Speaker-level RCV inputs Includes 2. 5mm allen wrench for installation the hd-rlc remotely controls the bass level of the following jl audio amplifiers:hd-series: all modelsXD-Series: All modelsMHD-Series: All modelsM-Series: M600/1, M500/3, M400/4, M200/2, M700/5, M600/6.

When the hd-rlc is connected to the above amplifiers, it acts as an attenuator on the input gain of the amplifier and is used to adjust the overall level of the amplifier from the front of the vehicle. The hd-rlc kit includes the rotary control with a black ABS knob, mounting hardware and one 18 ft. 4 gauge power and ground wiring is required for installation.

5. 5 m cable. Dimensions: 14 3/4"w x 7 1/8"L x 2"H.


Similar products

JL Audio HD-RLC Amplifier Remote Level Control and Cable
JL Audio XD400/4: 4 Channel Class D Full-Range Amplifier 400 Watts
JL Audio RBC1 Remote Bass Control
JL Audio XD600/6v2 6-channel car amplifier - 75 watts RMS x 6
Jl Audio 10tw3-d4 Shallow-mount 10
JL Audio XD-CLRAIC2-18 2-Channel Twisted-Pair Audio Interconnect Cable with Molded Connectors, 18-Feet
10W6v3-D4 - JL Audio 10" 600W Dual 4-Ohm Car Subwoofer
JL Audio XD400/4v2 4-channel car amplifier — 75 watts RMS x 4


JL Audio RBC1 Remote Bass Control

5. 5 m cable. Dimensions: 14 3/4"w x 7 1/8"L x 2"H. Remotely controls Bass EQ of JL Audio amplifiers. Low-profile design for custom installations. When the rbc-1 is connected, the on-board "Boost" control of the amplifier is defeated and the RBC-1 becomes the only active boost controller. The jl audio rbc-1 wired remote bass controller is designed to remotely control the Bass EQ boost or Input Level feature of JL Audio amplifier equipped with a "Remote Bass" or "Remote Level" port.

4 gauge power and ground wiring is required for installation. Remote bass control works with Original Slash Series JL Audio Amplifiers and the New V2 Slash. Overrides on-board boost control. The hd-rlc remotely controls the bass level of the following jl audio amplifiers:hd-series: all modelsXD-Series: All modelsMHD-Series: All modelsM-Series: M600/1, M500/3, M400/4, M700/5, M200/2, M600/6.

When the hd-rlc is connected to the above amplifiers, it acts as an attenuator on the input gain of the amplifier and is used to adjust the overall level of the amplifier from the front of the vehicle. The hd-rlc kit includes the rotary control with a black ABS knob, mounting hardware and one 18 ft.


Similar products

KnuKonceptz KCA Complete 4 Gauge Amp Installation Kit
JL Audio JX400/4D 4-channel car amplifier — 70 watts RMS x 4
JL Audio HD-RLC Amplifier Remote Level Control and Cable
Jl Audio 10tw3-d4 Shallow-mount 10
KnuKonceptz Red KCA Complete 4 Gauge Amplifier Installation Wiring Kit
JL Audio XD-CLRAIC2-18 2-Channel Twisted-Pair Audio Interconnect Cable with Molded Connectors, 18-Feet
AudioControl LC2i Black 2 Channel Line-Output Converter with AccuBASS


Dynamat 10455 18" x 32" x 0.067" Thick Self-Adhesive Sound Deadener with Xtreme Bulk Pack, Set of 9

Aluminum-coated for heat-resistance. Nine 18" x 32" sheets high tack permanent adhesive. Remotely controls Bass EQ of JL Audio amplifiers. High-performance dynamat xtreme is lighter than Dynamat Original, requires no heat to apply and is recommended for vehicle tops, four times more effective, sides and contoured areas.

Dynamat xtreme is coated with aluminum for high temperature areas such as firewalls and floors. 4 gauge power and ground wiring is required for installation. 5. 5 m cable. Dimensions: 14 3/4"w x 7 1/8"L x 2"H. Unlike dynamat original, dynamat Xtreme is also recommended for trunk lids, roofs, quarter panels and under-hood installations.

. The hd-rlc remotely controls the bass level of the following jl audio amplifiers:hd-series: all modelsXD-Series: All modelsMHD-Series: All modelsM-Series: M600/1, M400/4, M200/2, M500/3, M700/5, M600/6. When the hd-rlc is connected to the above amplifiers, it acts as an attenuator on the input gain of the amplifier and is used to adjust the overall level of the amplifier from the front of the vehicle.

The hd-rlc kit includes the rotary control with a black ABS knob, mounting hardware and one 18 ft. Low-profile design for custom installations. Kit contains nine 18" x 32" pieces of Dynamat Xtreme for rear decks, doors, floors and trunk floors.


Similar products

Dynamat 10007 Dyna-Roller Professional Heavy Duty Sound Deadener Installation Tool with Wood Handle and 2" Wide Rubber Roller
Dynamat 13100 1-1/2" Wide and 30' Long DynaTape Sound Deadener
Dynamat 11103 Dynaliner 32" x 54" x 1/2" Thick Self-Adhesive Sound Deadener
Dynamat 11102 Dynaliner 32" x 54" x 1/4" Thick Self-Adhesive Sound Deadener
Dynamat 13100 1-1/2" Wide and 30' Long DynaTape Sound Deadener (2-Pack)
Dynamat 21100 DynaPad 32" x 54" x 0.452" Thick Non-Adhesive Sound Deadener
Dynamat 10435 12" x 36" x 0.067" Thick Self-Adhesive Sound Deadener with Xtreme Door Kit
uxcell® Car Sound Deadener Application Rolling Wheel Roller 5cm x 3.5cm
Dynamat 11101 Dynaliner 32" x 54" x 1/8" Thick Self-Adhesive Sound Deadener
Dynamat 11905 Hoodliner 32" x 54" x 3/4" Thick Self-Adhesive Sound Deadener


JL Audio XD-CLRAIC2-18 2-Channel Twisted-Pair Audio Interconnect Cable with Molded Connectors, 18-Feet

Remotely controls Bass EQ of JL Audio amplifiers. Aluminum-coated for heat-resistance. Nine 18" x 32" sheets high tack permanent adhesive. Overrides on-board boost control. 18 ft. 5. 5 m cable. Dimensions: 14 3/4"w x 7 1/8"L x 2"H. 2-channel twisted-Pair Audio Interconnect Cable. Remote bass control works with Original Slash Series JL Audio Amplifiers and the New V2 Slash.

4 gauge power and ground wiring is required for installation. Twisted construction for increased quality. Low-profile design for custom installations. Length: 18 ft 5. 49 m. Increased flexibility. 5. 49 m 2-channel twisted-pair audio interconnect cable w/ molded connectors the hd-rlc remotely controls the bass level of the following jl audio amplifiers:hd-series: all modelsXD-Series: All modelsMHD-Series: All modelsM-Series: M600/1, M500/3, M400/4, M200/2, M700/5, M600/6.

When the hd-rlc is connected to the above amplifiers, it acts as an attenuator on the input gain of the amplifier and is used to adjust the overall level of the amplifier from the front of the vehicle. The hd-rlc kit includes the rotary control with a black ABS knob, mounting hardware and one 18 ft. Molded connector bodies for extended durability.




Similar products

JL Audio XD-CLRAIC4-18 4-Channel Twisted-Pair Audio Interconnect Cable with Molded Connectors, 18-Feet
JL Audio HD-RLC Amplifier Remote Level Control and Cable
JL Audio XD-PCS4-1B 4-AWG 12-Volt Power Connection for Single Amplifier 100-AMP Capacity
JL Audio RBC1 Remote Bass Control
JL Audio XD-CLRAIC2-3 2-Channel Twisted-Pair Audio Interconnect Cable with Molded Connectors, 3-Feet
JL Audio JX400/4D 4-channel car amplifier — 70 watts RMS x 4
Stinger SGW9920 9 Conductor Speedwire 20ft Roll Blue
JL Audio XD-CLRAIC2-6 2-Channel Twisted-Pair Audio Interconnect Cable with Molded Connectors, 6-Feet


Dynamat 13100 1-1/2" Wide and 30' Long DynaTape Sound Deadener

Pure oxygen free copper conductors with Polyethylene Dielectrics. Increased flexibility. New - Retail. One roll 1. 5 wide x 30 long 38mm x 9. 1m. 002 thick solid Aluminum Finishing Tape. 5. 5 m cable. Dimensions: 14 3/4"w x 7 1/8"L x 2"H. Molded connector bodies for extended durability. Transparent pressure sensitive adhesive the hd-rlc remotely controls the bass level of the following jl audio amplifiers:hd-series: all modelsXD-Series: All modelsMHD-Series: All modelsM-Series: M600/1, M200/2, M400/4, M500/3, M700/5, M600/6.

When the hd-rlc is connected to the above amplifiers, it acts as an attenuator on the input gain of the amplifier and is used to adjust the overall level of the amplifier from the front of the vehicle. The hd-rlc kit includes the rotary control with a black ABS knob, mounting hardware and one 18 ft. Low-profile design for custom installations.

1-year Warranty. Nine 18" x 32" sheets high tack permanent adhesive. 4 gauge power and ground wiring is required for installation. Aluminum-coated for heat-resistance. Overrides on-board boost control.


Similar products

Dynamat 10007 Dyna-Roller Professional Heavy Duty Sound Deadener Installation Tool with Wood Handle and 2" Wide Rubber Roller
Dynamat 10455 18" x 32" x 0.067" Thick Self-Adhesive Sound Deadener with Xtreme Bulk Pack, (Set of 9)
Extreme Dynamat Xtreme Bulk Pack Heat & Sound Deadening
Dynamat 10435 12" x 36" x 0.067" Thick Self-Adhesive Sound Deadener with Xtreme Door Kit
Dynamat 11102 Dynaliner 32" x 54" x 1/4" Thick Self-Adhesive Sound Deadener
Dynamat 10465 24" x 48" x 0.067" Thick Self-Adhesive Sound Deadener with Xtreme Mega Pack, (Set of 9)
Dynamat 11905 Hoodliner 32" x 54" x 3/4" Thick Self-Adhesive Sound Deadener
TMS Mass Loaded Vinyl 4' X 25' 100 Square Feet 1 Lb MLV Acoustic Barrier
Dynamat 11103 Dynaliner 32" x 54" x 1/2" Thick Self-Adhesive Sound Deadener
Dynamat 10425 18" x 32" x 0.067" Thick Self-Adhesive Sound Deadener with Xtreme Wedge Pack